Harbor Freight Tools 46092 User Manual

AUTO-DARKENING  
WELDING HELMET  
with ANSI Approved Lens  
46092  
ASSEMBLY AND OPERATING INSTRUCTIONS  
NOTE:YOUR Helmet may appear different from the Helmet pictured in this manual.  
The changes are only cosmetic, the warnings, operation instructions, and maintenance  
procedures will remain the same.  
3491 Mission Oaks Blvd., Camarillo, CA 93011  
TO PREVENT SERIOUS INJURY OR BLINDNESS,  
READ AND UNDERSTAND ALL WARNINGS  
AND INSTRUCTIONS BEFORE USE.  
©
®
Copyright 2004 by Harbor FreightTools . All rights reserved. No portion of this manual  
or any artwork contained herein may be reproduced in any shape or form without the express  
written consent of Harbor FreightTools.  
For technical questions and replacement parts, please call 1-800-444-3353  
Revised Manual 04/05; Revised Cover 06/05  
Safety Warnings and Precautions (continued)  
4. Keep children away. Children must never be allowed in the work area. Do not let them  
handle machines, tools, or extension cords.  
5. Store idle equipment. When not in use, tools must be stored in a dry location to inhibit  
rust. Always lock up tools and keep out of reach of children.  
6. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the  
work of a larger industrial tool. There are certain applications for which this tool was  
designed. Do not modify this tool and do not use this tool for a purpose for which it was  
not intended.  
7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving  
parts. Protective gear is essential to protect against welding rays, some examples are: a  
leather welding apron, welding sleeves, jeans without cuffs, work boots. Wear restrictive  
hair covering to contain long hair.  
8.  
Use eye and ear protection. When welding, wear ANSI approved impact  
safety goggles under the Auto-Darkening Welding Helmet. Wear an ANSI  
approved respirator and hearing protection when welding.  
9. Do not overreach. Keep proper footing and balance at all times. Do not reach over or  
across running machines.  
10. Stay alert. Watch what you are doing, use common sense.Do not operate any tool when  
you are tired.  
11. Check for damaged parts. Before using any tool, any part that appears damaged should  
be carefully checked to determine that it will operate properly and perform its intended  
function. Check for alignment and binding of moving parts; any broken parts or mounting  
fixtures;and any other condition that may affect proper operation.Any part that is damaged  
should be properly repaired or replaced by a qualified technician. Do not use the tool if  
any switch does not operate properly.  
12. Replacement parts and accessories. When servicing, use only identical replacement  
parts. Use of any other parts can render helmet ineffective, possibly causing eye damage,  
and will void the warranty. Only use accessories intended for use with this tool.Approved  
accessories are available from Harbor Freight Tools.  
13. Do not operate tool if under the influence of alcohol or drugs. Read warning labels  
on prescriptions to determine if your judgment or reflexes are impaired while taking drugs.  
If there is any doubt, do not operate the tool.  
14. Maintenance. For your safety, service and maintenance should be performed regularly  
only by a qualified technician.  
Warning:The warnings, cautions, and instructions discussed in this instruction manual  
cannot cover all possible conditions and situations that may occur. It must be under-  
stood by the operator that common sense and caution are factors which cannot be  
built into this product, but must be supplied by the operator.  
WARNING:This product is used with welding or similar applications that produce  
chemicals known to the State of California to cause cancer and birth defects (or  
other reproductive harm). (California Health & Safety Code 25249.5 et seq.)  
REV 05/04  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Page 3  
Welding Helmet Specific Safety Warnings and Precautions  
1.  
People with pacemakers should consult their physician(s) before welding.  
Electromagnetic fields (such as those caused by welding) in close proximity to a heart  
pacemaker could cause interference to or failure of the pacemaker.  
2. This helmet provides protection for intended purposes only.  
The Welding Helmet is not suitable for laser welding processes.  
TheWelding Helmet will not protect against severe impact hazards, including fragmenting  
grinding disks; never use Welding Helmet when grinding.  
The Welding Helmet will not protect against explosive devices or corrosive liquids.  
3. Use only at temperatures from 23 to 131° F.  
4. Maintain the helmet and lens correctly to help ensure reliable protection.  
Clean filter’s surfaces regularly. Always keep sensors and solar cells clean using a  
clean lint-free tissue/cloth. Don’t use any solvents on filter’s screen or helmet components.  
Protect filter from liquid and dirt contact. Don’t immerse the filter in water.  
Should the Auto-Darkening Welding Helmet not darken upon striking an arc, stop  
welding immediately and have the helmet checked by an authorized service  
technician.  
Regularly replace the Front Lens Cover (1) if it becomes cracked, scratched, pitted,  
or otherwise damaged.  
Do not make any modifications to either the Auto-Darkening Filter (2) or the rest of  
the helmet, other than those specified in this manual. Do not use any replacement  
parts other than those specified in this manual. Unauthorized modifications and  
replacement parts will void the warranty and expose the user to the risk of personal  
injury. Never open or tamper with the Auto-Darkening Filter (2).  
5. The Welding Helmet’s Auto-Darkening Filter (2) must never be placed on hot  
surfaces.  
WARNING: SEVERE PERSONAL INJURY and/or BLINDNESS may occur if  
the user fails to follow the aforementioned warnings and/or fails to follow  
the operation instructions.  
Warning: Read and understand all instructions before using!  
REV 05/04  
Page 4  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Unpacking  
When unpacking, check to make sure all the parts are included. Refer to the Parts List  
and Assembly Diagram at the end of this manual. If any parts are missing or broken, please  
call Harbor Freight Tools at the number on the cover of this manual as soon as possible.  
The Auto-Darkening Welding Helmet is designed to protect the eyes and face  
from sparks, splatter, and harmful radiation under normal welding conditions. The  
Auto-Darkening Filter automatically changes from a clear state to a dark state when  
an arc is struck, and it returns to the clear state when welding stops.  
The Auto-Darkening Welding Helmet comes ready for use. The only things  
you need to do before welding are to remove the protective film from both sides of  
the lens (if not already done), adjust the position of the headband, select the correct  
shade number for your application, and test the helmet for proper operation, as  
mentioned below.  
BEFORE WELDING  
Check the Front Cover Lens to makes sure that it is clean, and that no dirt is  
covering the two sensors on the front of the Filter Cartridge. Also check the Front/  
Inside Cover Lens and the Front Lens Retaining Frame, and make sure that they  
are secure in place.  
Inspect all operating parts before each use for signs of wear or damage. Any  
scratched, cracked, or pitted parts should be replaced immediately before using  
again to avoid severe personal injury.  
Check for light tightness before each use.  
Select the shade number you need for your setting at the turn of a shade knob  
(See Shade Guide Table on page 7). Finally, be sure that the shade number of the  
Welding Helmet is the correct shade number for your application. Note: If a  
selection of shades are recommended for your application, try the darkest setting  
first.  
Adjust headband so that the helmet is seated on the head as low as possible  
and close to your face. Adjust helmet’s angle when in the lowered position by  
turning the adjustable limitation washer.  
SHADE NUMBER SELECTION  
The shade number can be infinitely set manually between 9 - 13. Check with  
the Shade Guide Table on page 8 to determine the proper shade number for your  
application. To select a shade number, simply turn the shade knob until the arrow  
points to the desired shade number.  
IMPORTANT NOTE: Test the helmet auto-darkening filter lens before welding.  
While wearing the helmet, briefly strike an arc, keeping your face and eyes turned  
slightly away, and to one side. The lens should darken evenly when not directly  
facing the arc. If it does not darken properly, do not use theWelding Helmet.  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Page 5  
PRODUCT FEATURES  
At the moment the welding operation is started, the filter screen automatically  
changes from clear to dark in only 1/25,000th of a second.  
Dark to clear delay adjustment: Operator can vary the time for the filter to  
return to clear state.  
At the moment welding is stopped, the filter screen automatically changes  
from dark to clear state according to your preset time. Note: If the time-setting  
switch is at the “FAST” position - the time can vary from 0.25 seconds to 0.35  
seconds; if it is at the “SLOW” position - the time can vary from 0.6 seconds to 0.8  
seconds-see Figure 1, below.  
Figure 1  
(View from  
inside of  
helmet.)  
Dark to Clear Delay Adjustment  
In FAST Position = .25-.35 Second  
In SLOW Position = .60-.80 Second  
This Welding Helmet utilizes high performance solar cells as power supply,  
and has two built-in 3V lithium batteries as power backup. No change of battery is  
needed. Under normal welding conditions, users can expect a battery lifetime of  
more than 6 years.  
User-selectable (DIN) variable shades from 9 to 13 are adjusted at the turn of  
a shade knob (shade variable). This product is in full conformity with related DIN,  
ISO, EN379 safety standards and ANSI Z87.1-1989 standard.  
The ultra high performance of UV and IR Auto-Darkening filters provides to  
the user’s eyes and face full protection against UV and IR radiation during the entire  
welding process, even in the clear state. The UV/IR protection level is up to Shade  
14 (DIN) at all times.  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Page 6  
COMMON PROBLEMS AND REMEDIES  
1.  
2.  
Irregular Darkening or Dimming  
a. Headband has been set unevenly on the two sides of the helmet (unequal distances  
from the eyes to the filter’s lens).  
b. Reset headband to reduce the difference in distances to filter, if necessary.  
Auto-Darkening Filter Does Not Darken Or Flickers  
a. Front Cover Lens is soiled or damaged (change the cover lens).  
b. Sensors are soiled (clean surface of the sensors).  
c. Welding current is too low (turn the switch to the “SLOW” position, if necessary.  
Slow Response  
3.  
4.  
a. Operating temperature is too low (do not use at temperatures below 23° F).  
PoorVision  
a. Front/Inside Cover Lens and/or filter soiled (change it).  
b. Insufficient ambient light.  
c. Shade number is incorrectly set (reset shade number).  
Welding Helmet Slips  
5.  
a. Headband is not adjusted properly (must be lowered).  
WARNING: You must stop using the Auto-Darkening Welding  
Helmet IMMEDIATELY if any of the above mentioned  
problems can’t be corrected.  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Page 7  
LENS AND HELMET MAINTENANCE  
Figure 2  
1. Replace the Front Lens Cover (1) if it is damaged  
(cracked, scratched, soiled or pitted).  
a. Remove the Front Lens Cover (1) by gently pulling up the  
central part of the Lens -see Figure 2, right.  
b. Remove the protection film from both sides of the new Lens  
if it comes with the film on. Place the new Lens into the right  
position by bending it slightly, enough to fit in between the  
tabs at each side of the lens and putting the lens in place -  
see Figure 2.  
c. Check and make sure that the Lens is securely installed.  
2.  
3.  
Clean the Filter Lens with a clean lint-free tissue or cotton cloth.  
Don’t immerse the lens in water or any other liquid. Never use abrasives, solvents or oil  
based cleaners.  
4.  
5.  
Don’t remove the auto-darkening filter from the Auto-Darkening Welding Helmet. Never  
try to open the filter.  
Storage temperature: -13 to 167° F.  
Shade Guide Chart  
SKU 46092  
For technical questions, please call 1-800-444-3353.  
Page 8  
Parts List and Assembly Diagram  
1.Front Lens Retaining Frame  
2.Front Cover Lens  
3.Auto-Darkening Filter Cartridge  
4. Shade Knob  
6. Shell (Welding mask)  
7.Front Headband  
8. Adjustable Headband  
9. 2 x Block Nut  
11. 2 x Adjustable Limitation Washer  
12.Left Limitation Washer  
13. 2 x Screw  
14.Right LimitationWasher  
5. Inside Cover Lens  
10.4 x Washer  
* Includes Slow/Fast and Sensitivity Switches  
NOTE:Some parts are listed and shown for illustration purposes  
only and are not available individually as replacement parts.  
PLEASE READTHE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS  
MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR DISTRIBUTOR  
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR  
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS  
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER  
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS  
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE  
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER  
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING  
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTSTHERETO.  
REV 11/04  
Page 9  
SKU 46092  
For technical questions, please call 1-800-444-3353.  

Ariston 28 MFFI User Manual
Audiovox Jensen JPA1150M User Manual
Black Decker BLM2600G User Manual
Braun MR4050 CA User Manual
Canon Digital Camera 50D User Manual
Crestron electronic Crestron C2N CAMIDJ User Manual
Cuisinart FPB 5 User Manual
Emotiva DIFFERENTIAL REFERENCE XDA 1 User Manual
FujiFilm FinePix X100 User Manual
JVC Everio Digital Camcorder LYT1856 001C User Manual